Mr. 40's STUFF

'40 Ford Inner Fender Panels

Magazine Instruction Articles

Power Window Kits

Radiators

Radiator Hoses

Stereos / Speakers

Thermostats

Trunklift Kits

Trunklift Struts

V-Butt "Thang"

ELECTRIC COWL VENT KIT

UNDER-FENDER BATTERY BOX KIT

'40 FORD BODY BOLT KITS

* * *

FENDER PANEL MOUNTING BRACKETS

'39-'40 FORD INNER FENDER PANELS

WINDSHIELD GARNISH MOLDING

GRILLE SHROUDS AVAILABLE FOR'40 FORDS

* * *

Finally a battery location that is out-of-sight, close to the motor and easily accessible. The unused space tucked into the right side fender is perfect for our newest battery boxes. We know they work on '35 to '48 Ford frames cause we've run 'em there for years. They'll probably work in lots of other fat fendered cars too!

Waterjet-cut from 18ga. stainless steel, this box measures 10-1/2" wide, 7-1/2" tall, 6-3/4" from back to front, and uses 15-1/2" of frame-rail space. Kit comes with AVK industrial nutserts with stainless steel Allen head hardware and mounting tool for boxed or open frames.

Battery location means you can use shorter cables thus increasing voltage to your engine over trunk mount batteries.

Removing the splash guard and reinforcing the fender may be necessary. No hold down or battery strap needed...fender location keeps the battery from escaping the box.

40FBB-SS, Frame Mount Battery Box Stainless Steel $149.00

* * *

Eliminate those ugly stock bolt sets with these USA made stainless steel button head allen bolts and nylock nut kits. Our kits attach the 40 Ford front fenders/grill/inner panels together, with separate kits for running boards and rear fenders.

40 LBK, '40 Ford Frontend Clip Kit (16pcs) $45.00

40 LBK-FF/COWL, '40 Ford Front Fender to Cowl Kit (8pcs) $19.00

40 LBK-RB, '40 Ford Running Board Kit (22pcs) $82.00

40 LBK-RF-PASS, '40 Ford Rear Fender Kit (20pcs) $35.00

40 LBK-RF-PKP, '40 Ford Pickup Rear Fender Kit (14pcs) $55.00

40 LBK-ALL-PASS, '40 Ford Coupe/Sedan Complete Kit (66pcs) $173.00

# 40 LBK-ALL-PKP, '40 Ford Pickup Complete Kit (60pcs) $190.00

* * *

This kit is designed to allow use of your cowl vent when the handle space has been consumed by A/C, stereo & other underdash intrusions. Designed to bolt-in to most any cowl, the kit comes with firewall mounting bracket attached, (2) cowl vent control brackets, 12 volt US made motor, gear drive, stainless steel hardware, wiring, momentary pushbutton switch and illustrated instructions. Motor stops at any desired height and closes to seal as tight as originally set-up. Do yourself a "FRESH-AIR-FAVOR."

40ECV, Electric Cowl Vent Kit $219.00

(Measures 4" wide, 3" high & 3" deep)

Removing the stock front yoke on your Ford means stabalizing the front clip in other ways. These 1/8" thick steel bracket kits allow you to mount fender panels to adjacent frame rail for added front support and vibration reduction. All kits come with USA made stainless steel button head Allen bolts and Nylocks.

40FPK-S (Straight Brackets, Side Frame-Rail Mount) $65.00

Brackets Only, No Hardware $35.00 per pair

40FPK-L ("L"-Shapes, Top Frame-Rail Mount) $65.00

Brackets Only, No Hardware $35.00 per pair

* * *

REPLACEMENT STRUTS...$79.00 per pair.
You can bring your hoodlift up to snuff with a new pair of gas shocks. Call us with your make and model car and we will do the rest. All pairs are $79.00 plus shipping and handling. Struts include new nylon ball sockets.

We made 'em look cool... and that's the job they do by allowing the engine heat to exit and your ride to run cooler. Functional 3" Louvers are arranged so they actually scavenge the hot air out past the fender wells. Waterjet-cut out of heavy 16 gauge steel these panels will put strength back in your Fords front clip. These flat-style panels have all the right curves as well as oval-shaped mounting holes to make hanging and adjusting your front clip a little easier. Sale price is for pairs only. These panels fit all '39-'40 Ford Passenger Cars and '40-'41 Ford Pickups.

40SIP - SMOOTH INNER FENDER PANELS $329.00 pair

40LIP - LOUVERED INNER FENDER PANELS $450.00 pair
(40SIP & 40LIP fits stock '40 chassis with axle front suspension, will also fit aftermarket chassis with IFS or Mustang II when you cut out the section to clear the upper "A" arms with a plasma cutter or nibbler.)

40LIP-SC - LOUVERED INNER FENDER PANELS-SUPER COOLERS $500.00 pair

(94 TOTAL LOUVERS - recommended for straight axels only)

We don't have a clue what Henry called them...we do know most everybody with our V-Butted windshields needs to cover the gap in the garnish molding where it comes together in the center above the dash. We tooled up and reproduced the part that came originally on '40 pickups at the top of the windshield. Removing the center divider bar leaves a big ugly hole and now you can cover it up.

40VBT '40 V-Butt Thang $24.00

* * *

Our 18 gauge steel over-the-grill shrouds perform double duty on 1940 Fords and '39 Deluxe Fords by hiding the clutter, plus help direct incoming air through the radiator and not over it. Grille shrouds help your '40 run cooler and make your engine compartment look a whole lot better with the hood up. Comes undrilled so mounting method can be of your choice. Available with hole cut out for stock latch assembly or solid for mounting an aftermarket latch or as a pass-thru piece. Standard or Deluxe Grill Models.

Grill Shrouds for '40 Ford Standard, '40-'41 Pickups &

'39 Deluxe Passenger

40GSS-SNH, GRILL SHROUD STANDARD - STEEL NO HOLE $99.00

40GSS-SWH, GRILL SHROUD STANDARD - STEEL with STOCK LATCH HOLE $99.00

Grill Shrouds for

'40 Ford Deluxe Models

40GSD-SNH, GRILL SHROUD DELUXE - STEEL NO HOLE $99.00

40GSD-SWH, GRILL SHROUD DELUXE - STEEL with LATCH HOLE $99.00

* * *

HOODLIFTS KITS AVAILABLE FOR

'39 - '40 FORDS

Raises the hood on '39 Deluxe and all '40 model Fords, plus our newest kit now for '40 and '41 Ford pickups. Very easy to mount with clear instructions. Gas springs clear most A/C and heater hoses. Some hood hinge adjustment may be necessary for proper hood alignment.

40HLP, Fits '39 Deluxe and '40 Fords $149

40HLPK, Fits '40-'41 Ford PIckup Passenger Hoodlift Kit $129

CHEVY / GM / WILLYS APPLICATIONS

34CCTL, Fits '28-'34 Chevy/GM Coupe $159

36CCTL, Fits '35-'36 Chevy/GM Coupe $159

38CCTL, Fits '37-'38 Chevy/GM Coupe & Bus Coupe $169

39CCTL, Fits '39 Chevy/GM Coupe $169

40CCTL, Fits '40 Chevy/GM Coupe $169

48CCTL, Fits '41-'48 Chevy/GM Coupe $169

36CSTL, Fits '35-'36 Chevy/GM Sedan $169

38CSTL, Fits '37-'39 Chevy/GM Sedan $169

40CSTL, Fits '40 Chevy/GM Sedan $129

48CSTL, Fits '41-'48 Chevy/GM Sedan $179

40WCTL, Fits '39-.41 Willys Coupe $179

REPLACEMENT STRUTS $79.00 per pair.
Yes we've been making TRUNKLIFT KITS since 1985 now and some of the older ones are starting to get droopy. You can bring your decklid up to snuff with a new pair of gas shocks. Call us with your make and model car and we will do the rest. All pairs are $79.00 plus shipping and handling. Struts include new nylon ball sockets.

FORD APPLICATIONS

32FCTL, Fits '28-'34 Ford Coupe & Roadster $159

32FGTL, Fits '28-'34 Fiberglass Ford Coupe & Roadster $169

36FCTL, Fits '35-'36 Ford Coupe Steel & Glass $159

37FCTL, Fits '37-'38 Ford Coupe $179

40FCTL, Fits '39-'40 Ford & Merc $159

48FCTL, Fits '42-'48 Ford & Merc Coupe & Convertible $159

36FSTL, Fits '35-'36 Ford Sedan $169

37FSTL, Fits '37-'38 Ford Sedan $179

40FSTL, Fits '39-'48 Ford Sedan $169

40FCVTL, Fits '40 Ford Convertible $169

'40 Ford Convertible application not available

41FCTL, Fits '41 Ford Coupe $159

TRUNKLIFTS KITS AVAILABLE FOR

1928-1948 FORD / CHEVY / GM / WILLYS

The "Trunklift Kit" Experts

Manufactured by Mr.40's, our TRUNKLIFT KITS replace all manor of stay-up poles and worn-out stock hardware. TRUNKLIFTS will raise most trunklids after the latch is released, and then hold it in the highest possible position until you are ready to close it. Most kits are engineered to use the available stock holes with very little installation time required. All TRUNKLIFTS contain exstension force gas struts designed to fit each application, custom made brackets, stainless steel Allen-Head hardware, ballstuds with nylocks and illustrated instructions. Some kits contain AVK industrial nutserts with stainless steel hardware for one-side surface mounting.